危廢貯存間建設需嚴格遵循 《危險廢物貯存污染控制標準》（GB18597-2023）和 《危險廢物收集貯存運輸技術規范》（HJ2025-2012），同時結合《建設項目危險廢物環境影響評價指南》要求，從 “設施建設” 和 “日常管理” 兩大維度落實規范，具體內容如下：

　　The construction of hazardous waste storage rooms must strictly comply with the "Pollution Control Standards for Hazardous Waste Storage" (GB18597-2023) and the "Technical Specifications for Collection, Storage, and Transportation of Hazardous Waste" (HJ2025-2012). At the same time, in accordance with the requirements of the "Guidelines for Environmental Impact Assessment of Hazardous Waste in Construction Projects", the specifications should be implemented from the two dimensions of "facility construction" and "daily management". The specific contents are as follows:

　　一、危廢貯存間建設規范：

　　1、 Construction standards for hazardous waste storage rooms:

　　按貯存設施類型分類落實根據危廢特性與貯存形式，貯存設施分為貯存庫、貯存場、貯存池、貯存罐區、貯存點五類，每類設施需滿足針對性污染控制要求，核心建設要點如下：

　　According to the characteristics and storage forms of hazardous waste, storage facilities are classified into five types: storage warehouses, storage yards, storage pools, storage tank areas, and storage points. Each type of facility must meet targeted pollution control requirements. The core construction points are as follows:

　　1. 通用基礎要求（所有類型設施均需滿足）監控與標識：配備內外全覆蓋的視頻監控設施；設置統一規范的 “貯存設施標識牌”（含危廢類別、管理制度、應急聯系方式），同時在分區處設置 “分區標識牌”。配套設備：配置稱重設備（用于臺賬記錄重量）、應急與消防物資（如滅火器、防泄漏工具、防護裝備等），確保應急需求。地面處理：所有貯存場所地面需硬化，存放液態 / 半固態危廢容器的區域，需做耐腐蝕硬化處理（涂覆至少 2mm 厚高密度環氧樹脂，表面無裂隙）。

　　1. General basic requirements (all types of facilities must meet) Monitoring and identification: equipped with fully covered video surveillance facilities both inside and outside; Set up unified and standardized "storage facility identification signs" (including hazardous waste categories, management systems, emergency contact information), and also set up "zone identification signs" at designated areas. Supporting equipment: equipped with weighing devices (for recording weight in the ledger), emergency and fire-fighting supplies (such as fire extinguishers, leak prevention tools, protective equipment, etc.), to ensure emergency needs. Ground treatment: All storage areas must have hardened floors, and areas storing liquid/semi-solid hazardous waste containers must undergo corrosion-resistant hardening treatment (coated with at least 2mm thick high-density epoxy resin, with no cracks on the surface).

　　2. 分類型設施建設要點設施類型適用場景核心建設要求貯存庫（倉庫式）多種類、多形態危廢（含液態、易揮發類）

　　2. Key points for facility construction by type, applicable scenarios, core construction requirements, storage facilities (warehouse style), multiple types and forms of hazardous waste (including liquid and volatile types)

　　1.?分區隔離：不同類別危廢分區存放，用過道、隔板或隔墻隔離，避免混存；

　　1. Partition isolation: Hazardous waste of different categories should be stored in separate areas, separated by corridors, partitions, or walls to avoid mixing;

　　2.?防泄漏設計：貯存液態 / 易產生滲濾液的危廢時，需配備 “泄漏堵截設施” 和 “滲濾液收集設施”：

　　2. Leak prevention design: When storing liquid/hazardous waste that is prone to producing leachate, "leak interception facilities" and "leachate collection facilities" should be equipped:

　　- 泄漏堵截設施容積：取 “對應區域最大液態危廢容器容積” 和 “液態危廢總儲量 1/10” 中的較大值；

　　-Leakage interception facility volume: take the larger of the "maximum liquid hazardous waste container volume in the corresponding area" and "1/10 of the total liquid hazardous waste storage capacity";

　　- 滲濾液收集設施容積：滿足實際收集需求；

　　-Capacity of leachate collection facilities: meets actual collection needs;

　　3.?廢氣治理：易產生粉塵、VOCs、酸霧的危廢，需安裝氣體收集裝置 + 凈化設施，排氣筒高度符合《大氣污染物綜合排放標準》（GB16297-1996）。貯存場（半開放式，帶頂棚）大量低揮發固態危廢1.?防雨水沖刷：設置徑流疏導系統，能抵御當?shù)刂噩F(xiàn)期≥25 年的暴雨，防止雨水進入貯存區；

　　3. Waste gas treatment: prone to generating dust VOCs、 The hazardous waste of acid mist requires the installation of gas collection devices and purification facilities, and the height of the exhaust pipe should comply with the Comprehensive Emission Standards for Air Pollutants (GB16297-1996). Storage site (semi open, with roof) for a large amount of low volatile solid hazardous waste? Rainwater erosion prevention: a runoff diversion system is set to resist the local rainstorm with a return period of ≥ 25 years and prevent rainwater from entering the storage area;

　　2.?液體收集：整體或分區設計液體導流 / 收集設施，容積需容納最不利情況下的滲濾液、廢水；

　　2. Liquid collection: Design liquid diversion/collection facilities as a whole or in zones, with a capacity to accommodate the worst-case scenario of leachate and wastewater;

　　3.?防滲與防揚散：危廢直接接觸地面時，基礎需做防滲處理（二選一）：

　　3. Anti seepage and anti scattering: When hazardous waste comes into direct contact with the ground, the foundation needs to be treated with anti-seepage measures (either option):

　　- 至少 1 米厚黏土層（滲透系數≤10??cm/s）；

　　-At least 1 meter thick clay layer (permeability coefficient ≤ 10 μ m/s);

　　- 至少 2mm 厚高密度聚乙烯膜等人工防滲材料（滲透系數≤10???cm/s）；

　　-At least 2mm thick high-density polyethylene film and other artificial anti-seepage materials (permeability coefficient ≤ 10 cm/s);

　　- 采取覆蓋、圍擋等措施防止危廢揚散、流失。貯存池（池體形式，室內 / 帶頂棚）單一類別液態 / 半固態危廢1.?全范圍防滲：防滲層覆蓋整個池體及基礎，確保無滲漏；

　　-Take measures such as covering and fencing to prevent the dispersion and loss of hazardous waste. Storage tank (tank form, indoor/with roof) for single category liquid/semi-solid hazardous waste 1? Full range anti-seepage: The anti-seepage layer covers the entire pool body and foundation to ensure no leakage;

　　2.?防雨水侵入：設施能抵御重現期≥25 年的暴雨，避免雨水、地面徑流進入；

　　2.? Rain water intrusion prevention: the facilities can resist rainstorm with a return period of ≥ 25 years, and prevent rainwater and surface runoff from entering;

　　3.?廢氣控制：減少大氣污染物無組織排放，必要時配備廢氣治理設施。貯存罐區（固定式，含罐體 + 輔助設施）液態危廢1.?圍堰防護：罐體必須置于圍堰內，圍堰需滿足防滲、防腐要求；

　　3. Waste gas control: Reduce unorganized emissions of air pollutants and equip waste gas treatment facilities if necessary. Storage tank area (fixed, including tank and auxiliary facilities) for liquid hazardous waste 1? Cofferdam protection: The tank must be placed inside the cofferdam, which must meet the requirements of anti-seepage and anti-corrosion;

　　2.?圍堰容積：至少能容納區內最大貯存罐意外泄漏的全部危廢量；

　　2. Capacity of the cofferdam: at least able to accommodate the total amount of hazardous waste accidentally leaked from the largest storage tank in the area;

　　3.?液體處理：圍堰內收集的廢液、廢水、初期雨水需及時處理，禁止直接排放。貯存點（簡易貯存設施）少量、臨時存放的危廢需滿足 “地面硬化、防泄漏、標識清晰” 基礎要求，具體參照對應危廢形態的防護標準（如固態危廢防揚散、液態危廢防滲漏）。

　　3. Liquid treatment: Waste liquid, wastewater, and initial rainwater collected within the cofferdam must be treated promptly and direct discharge is prohibited. The storage point (simple storage facility) should meet the basic requirements of "ground hardening, leak prevention, and clear labeling" for small and temporarily stored hazardous waste, and refer to the corresponding protection standards for hazardous waste forms (such as solid hazardous waste anti scattering, liquid hazardous waste anti leakage).

　　二、危廢貯存間管理規范：

　　2、 Management Regulations for Hazardous Waste Storage Room:

　　從 “物資管理” 到 “臺賬與應急” 全流程管控

　　From "material management" to "ledger and emergency" full process control

　　1. 設施與物資管理防泄漏配套管理：

　　1. Facility and material management, leak prevention and supporting management:

　　- 存放固態 / 半固態危廢時，設置收料托盤，用于收集泄漏物料；- 倉庫內設置防泄漏收集導流溝渠，溝渠連接至收集池，收集池容積不低于 “最大容器容量” 或 “危廢儲量 1/5” 中的較大值；- 易產生粉塵、VOCs、酸霧的危廢，必須裝入閉口容器 / 包裝物內貯存，廢氣排放需符合《大氣污染物綜合排放標準》（GB16297）和《揮發性有機物無組織排放控制標準》（GB37822）。應急與安全管理：- 倉庫內及出入口處設置 24 小時視頻監控，確保無死角；- 配備安全照明（燈具、線路需滿足防爆要求）；- 按風險等級配備對應應急物資（如防腐蝕手套、護目鏡、吸附棉、滅火器等），存放于應急物資柜，定期檢查補充；- 空包裝桶 / 容器需放在卡板上，堆疊整齊并纏繞拉伸膜固定，張貼危廢二維碼標簽，避免二次污染。

　　-When storing solid/semi-solid hazardous waste, set up a receiving tray to collect leaked materials; -Set up leak proof collection and diversion channels in the warehouse, which are connected to collection tanks with a capacity not less than the larger of "maximum container capacity" or "hazardous waste storage capacity 1/5"; -Easy to generate dust VOCs、 The hazardous waste of acid mist must be stored in closed containers/packaging materials, and the exhaust emissions must comply with the Comprehensive Emission Standards for Air Pollutants (GB16297) and the Unorganized Emission Control Standards for Volatile Organic Compounds (GB37822). Emergency and safety management: Set up 24-hour video surveillance in the warehouse and at entrances and exits to ensure no blind spots; -Equipped with safety lighting (lamps and circuits must meet explosion-proof requirements); -Equip corresponding emergency supplies (such as anti-corrosion gloves, goggles, absorbent cotton, fire extinguishers, etc.) according to the risk level, store them in emergency supply cabinets, and regularly inspect and replenish them; -Empty packaging drums/containers should be placed on pallets, stacked neatly and secured with stretch film, and labeled with hazardous waste QR codes to avoid secondary pollution.

　　2. 標識與標簽管理

　　2. Identification and label management

　?。?）危險廢物標簽：附著于容器 / 包裝物內容要素（缺一不可）：廢物名稱、類別代碼（依據《國家危險廢物名錄》）、危險特性標識（腐蝕性 / 毒性 / 易燃性 / 反應性）、主要 / 有害成分、產生單位及聯系人、數字識別碼（唯一追溯編碼）、二維碼、產生日期與重量、注意事項。設置要求：- 位置：容器明顯可見處（箱類端面 / 側面、桶類桶身 / 桶蓋、袋類表面），避免遮擋或污染；- 尺寸：按容積分級 ——≤50L 用 100×100mm、＞50~≤450L 用 150×150mm、＞450L 用 200×200mm；- 材質：防水耐用（如不干膠覆膜、塑封）；- 特殊情形：無包裝危廢需設置柱式標志牌替代標簽。

　　(1) Hazardous waste label: attached to the content elements of the container/packaging (indispensable): waste name, category code (based on the National Hazardous Waste List), hazardous characteristic identification (corrosive/toxic/flammable/reactive), main/harmful components, production unit and contact person, digital identification code (unique traceability code), QR code, production date and weight, precautions. Setting requirements: - Location: Clearly visible parts of the container (box end face/side, barrel body/lid, bag surface), avoiding obstruction or contamination; -Size: Classified by volume - ≤ 50L uses 100 × 100mm,>50~≤ 450L uses 150 × 150mm,>450L uses 200 × 200mm; - Material: Waterproof and durable (such as adhesive film, plastic sealing); -Special circumstances: Unpackaged hazardous waste requires column type signs to replace labels.

　　（2）貯存分區標志：置于設施內部，可視化管理制作要求：- 背景色：黃色（RGB255,255,0）或橙色（RGB255,150,0），字體為黑體，“危險廢物貯存分區標志” 字樣加粗居中；- 尺寸：按觀察距離確定（見下表）設置細則：- 分區依據：按危廢類別、形態及相容性劃分，避免不相容危廢混存（如 HW08 廢機油與 HW12 廢油漆渣分開）；- 位置：每個分區入口處的通道、墻壁或欄桿等易觀察位置；- 更新：隨貯存危廢種類變化動態調整標志內容。

　　(2) Storage zone sign: placed inside the facility, visual management production requirements: - Background color: yellow (RGB255255,0) or orange (RGB255150,0), font is in bold, and the words "Hazardous Waste Storage Zone Sign" are bolded and centered; -Size: determined by observation distance (see table below) Setting rules: - Zoning basis: divided by hazardous waste category, form, and compatibility to avoid incompatible hazardous waste mixing (such as separating HW08 waste engine oil from HW12 waste oil paint residue); -Location: easily observable locations such as passages, walls, or railings at the entrance of each partition; -Update: Dynamically adjust the content of the label according to changes in the type of hazardous waste stored.

　　3. 臺賬與追溯管理建立貯存臺賬：

　　3. Establish a storage ledger for ledger and traceability management:

　　通過 “實驗室綜合管理平臺” 或紙質臺賬，如實記錄危廢 “入庫 - 貯存 - 出庫” 全流程，內容包括：廢物名稱、類別代碼、重量、產生日期、貯存位置、出庫去向（如轉移至處置單位）、經辦人等；信息化追溯：所有危廢容器張貼二維碼標簽，掃碼可查詢臺賬信息，實現 “一物一碼” 追溯；臺賬保存：至少保存 5 年，以備監管部門核查。

　　Through the "Laboratory Comprehensive Management Platform" or paper ledger, truthfully record the entire process of hazardous waste "inbound storage outbound", including waste name, category code, weight, generation date, storage location, outbound destination (such as transfer to disposal unit), handler, etc; Information traceability: All hazardous waste containers are labeled with QR codes, which can be scanned to query ledger information and achieve "one item, one code" traceability; Record keeping: Keep for at least 5 years for regulatory authorities to verify.

　　4. 特殊管理要求禁止混存：

　　4. Special management requirements prohibit mixing:

　　不相容危廢（如酸性與堿性危廢、易燃與氧化性危廢）必須分區隔離，嚴禁混存；- 貯存時限：一般危廢貯存時限不超過 1 年，確需延長的需向當?shù)厣鷳B(tài)環境部門申請；- 定期檢查：每日巡查貯存設施是否破損、泄漏，每周檢查應急物資是否完好，每月核對臺賬與實際貯存危廢是否一致，發現問題及時整改。

　　Incompatible hazardous waste (such as acidic and alkaline hazardous waste, flammable and oxidizing hazardous waste) must be segregated and strictly prohibited from being stored together; -Storage time limit: Generally, the storage time limit for hazardous waste should not exceed one year. If an extension is necessary, an application must be made to the local ecological and environmental department; -Regular inspection: Daily inspection of storage facilities for damage and leakage, weekly inspection of emergency supplies for integrity, monthly verification of ledger and actual storage of hazardous waste for consistency, and timely rectification of any problems found.